Check out local project showcases!

18 showcases shown.

• 
  Bay Lake, MN

  Cracked Concrete Garage Floor Gets a Full Coating Upgrade

  Here's what we were working with before we got started - a worn concrete floor with visible cracking, staining, and years of use written all over it. The kind of floor most people just live with because they figure it's "just a garage." But a garage floor takes a beating every single day, and bare concrete is porous, hard to clean, and only gets worse over time. We applied a full polyurea flake coating system - floor to wall edge, no shortcuts. The prep work is everything on a job like this. You have to grind the concrete down properly before anything goes on, or the coating won't bond the way it needs to. We don't skip that step. Ever. The result is a coating that's locked in tight and built to hold up under real use. The color we went with is a light neutral blend that looks sharp against the stone exterior of this home. We also ran the coating up the base of the walls as a cove - that detail right at the floor-wall junction makes cleanup way easier and gives the whole space a much cleaner, finished look. It's a small thing that makes a big difference. What you end up with is a floor that's resistant to oil, chemicals, and moisture - and way easier to sweep or mop clean. No more watching stains soak straight into the concrete. The textured flake surface also adds grip underfoot, which matters in a space where you're walking in with wet shoes or moving things around. Every floor has its own quirks - different concrete conditions, different layouts, different levels of wear. We look at all of it before we start, and we coat accordingly. That's how you get a result that actually lasts instead of one that peels up two years down the road.
• 
  Saint Joseph, MN

  Cracked Garage Floor Gets a Fresh Coat in St. Joe

  Chuck and Diane's garage floor had seen better days. Cracks running across the slab, oil stains soaked into the concrete, and a generally worn-out surface that made the whole space feel rough and neglected. It's one of those things you walk past every day and think - yeah, that needs to get done eventually. Well, eventually finally came. Before we put down anything, the floor had to be properly prepped. That's not a step we skip. Grinding the surface opens up the concrete so the coating actually bonds instead of just sitting on top. It's the difference between a floor that lasts years and one that starts peeling after a season. You can see in the before shots just how rough and stained that slab was - not exactly a simple paint-and-go situation. We went with our Olive Grove finish for this one. It's a full broadcast flake system - color flakes are scattered across the base coat and then locked in with a clear topcoat. The result is a floor that looks sharp, handles foot traffic and vehicle weight without complaint, and is genuinely easy to clean. Oil, dirt, water - it wipes right up instead of soaking in. What we ended up with is a completely different space. The Olive Grove blend pulls in warm neutral tones that work well in a garage setting - not flashy, just clean and well-done. The floor reflects light better too, which makes the whole garage feel brighter and more organized even before you move a single thing around. A coated floor does more than look good. It protects the concrete underneath from moisture, staining, and further cracking. For Chuck and Diane, that worn-out slab is now a durable surface they won't have to think about for a long time. If your garage floor is in a similar spot, this is exactly the kind of work we do.
• 
  Cold Spring, MN

  Cracked Garage Floor Gets Slatestone Epoxy Coating in Cold Spring

  This garage floor had seen better days. Deep cracks running wall to wall, staining, and surface deterioration that only gets worse with Minnesota winters. A lot of homeowners in Cold Spring put up with floors like this for years because they assume replacement is the only option. It's not. We prepped the existing concrete and applied a full flake Polyurea & Polyaspartic coating in Slatestone - one of our most popular color options for a reason. Slatestone is a blend of two greys and white. It's sharp without being flashy. Neutral enough to go with any garage setup, and it just looks clean. The flake system isn't just about looks either. The texture you're seeing in the close-up shot gives the floor real grip underfoot, which matters when you're walking in from a wet driveway. And unlike bare concrete, this surface won't absorb oil drips, won't dust, and is a lot easier to sweep and clean. We coated the full floor surface including the step leading into the house - no skipping corners. That kind of detail matters. When everything gets the same treatment, the finished product looks intentional and polished, not like a patch job. If you've got a garage floor in the Cold Spring area that looks anything like the before photos here, it's worth knowing that a coating system like this is a straightforward fix. No need to tear out and repour. We work directly over the existing slab and the results speak for themselves.
• 
  Nisswa, MN

  Garage Floor and Patio Coatings in Nisswa MN

  This Nisswa property got the full treatment - garage floor coating and a patio coating done at the same time, both in the same Twilight flake blend. The color ties the two spaces together in a way that just looks intentional. Sharp inside, sharp outside. We use a polyurea and polyaspartic system on every job. There's a reason for that. It bonds harder, cures faster, and doesn't go soft in hot temps the way standard epoxy can. The surface ends up non-porous, which means oil, dirt, and water sit on top instead of soaking in. Cleaning it is genuinely easy - a mop or a hose gets it done. The flake broadcast goes wall to wall, and we run the coating up the base of the walls to keep that tight, finished look along the edges. The gloss topcoat does two things: it seals everything in and makes the space feel noticeably brighter. A garage that gets more use tends to be one that looks good to work in. The patio got the same full flake broadcast across the entire surface - rounded edges and all. A patio coating like this holds up to foot traffic, furniture, and whatever Minnesota weather throws at it. It won't peel, pit, or fade the way bare concrete does over time. The surface also adds a bit of texture that makes it safer underfoot when it's wet. Whether you're working with a garage, a patio, or both - the system is the same and the results hold up the same way. It's one of those upgrades that makes everyday use of your space a lot better without a lot of ongoing maintenance.
• 
  Little Falls, MN

  Front Porch Concrete Coating Refresh in Madras

  The before here tells a familiar story. Crumbling edges, peeling concrete, and a surface that's just worn down from years of weather and foot traffic. It's the kind of thing you walk past every day and think 'I really need to do something about that' - but never quite get to. That's exactly what we were dealing with on this front porch in Madras. What we applied is a broadcast chip concrete coating system. It's tough, it bonds directly to the existing slab, and it gives the surface a texture that actually grips underfoot - which matters a lot on steps especially. No more slick, bare concrete when it's wet outside. The coating wraps the steps and the full porch deck in one continuous finish, which is a big part of what makes it look so clean and intentional when it's done. The color and texture work really well with the brick exterior on this home. That neutral charcoal-and-tan chip blend doesn't fight the surroundings - it just pulls everything together. That's something we think about with every porch coating job. The surface has to make sense with the rest of the house, not stick out like an afterthought. What a lot of homeowners don't realize is that a coating like this does more than just look good. It seals the concrete and protects it from moisture, freeze-thaw cycles, and surface wear. That crumbling edge damage you often see on older porches? That's moisture getting in and doing its thing over time. A proper coating puts a stop to that and buys the slab a lot more life. The entry to your home is the first thing people see. A beat-up porch undercuts everything else you've done to keep the place looking sharp. A concrete coating is one of the more straightforward ways to fix that - and the results hold up.
• 
  St. Cloud, MN

  Concrete Basement Steps Get a Durable Coating Upgrade

  Most people think about coating their basement floor but forget about the steps. That's a mistake. Stairs take a beating - foot traffic, scuffs, grit tracked in from outside - and bare concrete just doesn't hold up well over time. It gets dusty, stained, and worn down in a way that's hard to clean no matter how much you scrub. Here's what we were working with: raw, pitted concrete stairs leading down into the basement, with surrounding vertical surfaces that were just as rough and dingy. The whole area had that tired, unfinished look that a lot of basements have. Functional, sure - but nothing you'd want to spend time in. We coated the stairs, the landing, and the surrounding verticals with the same durable coating system we use on basement floors. The flake broadcast gives it that clean, finished look you can see in the after - but it also adds grip, which matters a lot on stairs. And because the coating seals the surface, cleaning becomes a quick wipe rather than a chore. The biggest thing people notice after a job like this is how much more finished the whole space feels. It's not just the stairs - it's the way the coating ties the entire area together. No more chalky concrete dust. No more staining that grinds into the surface. Just a hard, sealed finish that actually holds up. A lot of homeowners don't realize that basement floor coatings can go well beyond just the main floor. Steps, landings, verticals - we can coat all of it and make the whole space look like it belongs together. If your basement stairs are overdue for an upgrade, this is exactly the kind of work we do.
• 
  Baxter, MN

  Front Step Concrete Coating in Brainerd MN Gets a Grip

  Front steps take a beating. They sit outside through every season, collect stains, start cracking along the edges, and over time they just look beat. Worse, smooth concrete steps get slick - and that's a real problem when you've got family and guests coming and going. That's exactly the situation we had here. The existing steps were showing their age. Staining, surface wear, and visible cracking along the risers - nothing structurally catastrophic, but enough to make the whole entry feel tired and a little sketchy underfoot. Not a great first impression, and not exactly safe. We applied a full concrete coating in Cabin Fever - a warm, earthy blend that works really well against the existing siding and that rich brown front door. But here's the part that matters most on steps: we added extra texture to the top coat. That added grip is especially important on a high-traffic surface where a slip could actually hurt someone. It's not just cosmetic, it's practical. The finished surface wraps every tread and riser clean and consistent. The coating bonds directly to the concrete, so it's not going anywhere. It handles foot traffic, weather, and the day-to-day without peeling or flaking like paint would. And it looks sharp doing it - the kind of entry that actually makes people notice the house in a good way. If your front steps are cracked, stained, or just plain slippery, a coating like this is one of the more straightforward upgrades you can make to your home's entry. It checks every box - looks better, lasts longer, and keeps people safer.
• 
  Sylvan, MN

  Deb's garage floor had seen better days. The old paint was chipping off in patches, leaving behind a rough, blotchy surface that collected dirt and looked worn no matter how much you cleaned it. That's one of the most common things we run into - old paint or coating that's failing and making the whole space feel neglected. Before we put anything down, we stripped all of that old material off and ground the concrete back to a clean, uniform surface. That step matters more than most people realize. A coating is only as good as what it bonds to. If you skip the prep, you're setting yourself up for the same peeling problem down the road. Once the surface was prepped and ready, we applied our Latte coating - a warm, neutral tone with a full broadcast flake that gives the floor real depth and texture. It's a popular pick for good reason. It hides minor imperfections, it's slip-resistant underfoot, and it holds up against oil, chemicals, and everyday garage traffic without breaking a sweat. The difference between the before and after here is hard to miss. What used to be a patchy, tired-looking floor is now clean, consistent, and sharp from wall to wall. And the practical side is just as good as the looks - a coated floor like this wipes down in minutes and doesn't absorb stains the way bare concrete does. We're proud to work with homeowners like Deb right here in central Minnesota. If your garage floor is in similar shape - chipped, stained, or just plain rough - this is exactly the kind of work we do every day.
• 
  Little Falls, MN

  Twilight Garage Floor Coating That Actually Gets Used

  Most garage floors just sit there looking rough. Stained concrete, dusty surface, maybe a few cracks - the kind of floor you tolerate rather than appreciate. The Twilight color we used on this one changed all of that. Dark base, black and white flake broadcast, sealed topcoat. It looks sharp, and more importantly, it holds up to everything a real working garage throws at it. What we love about a color like Twilight is how it handles a busy space. This garage is clearly being used - tools on the wall, equipment stored along the sides, everyday stuff. The floor doesn't compete with any of it. It just ties the whole space together and makes it feel intentional instead of thrown together. The coating itself is built for real garage conditions. Oil drips, foot traffic, the occasional scrape from a ladder or tool - none of that is going to phase a properly installed flake coating with a polyurea topcoat. That sealed surface is also a lot easier to sweep and mop than raw concrete, which tends to hold onto dust and grime no matter what you do. One thing worth pointing out - the edge work on this floor is clean all the way to the walls. That kind of detail matters. A floor that's coated tight to every edge looks finished. Sloppy edges undercut the whole job, even if the rest of the floor looks great. We don't cut corners there. If your concrete is sitting there looking tired and you've been putting this off, this is the kind of result that makes it worth getting done. A garage floor coating isn't just cosmetic - it protects the slab and makes the space genuinely easier to live with day to day.
• 
  St. Cloud, MN

  Commercial Garage Floor Coating in St. Cloud for Heartland 4x4

  This one was a real before-and-after. The floor at Heartland 4x4 in St. Cloud had seen better days - stained concrete, worn surface, old tile adhesive residue still clinging everywhere. Not exactly the kind of floor that impresses customers walking through the door. We went with the Domino color blend for this one. It's a black and white flake mix that hits that clean, sharp look without being fussy about it. For a shop that deals with 4x4 builds and off-road rigs day in and day out, it needed to be more than just good looking - it needed to hold up. That's where a full broadcast flake coating system earns its keep. The flakes get embedded into the base coat wall to wall, then sealed under a tough topcoat. The result is a surface that resists oil, hydraulic fluid, and general shop grime - and when it does get dirty, a quick sweep or mop takes care of it. No scrubbing concrete. No staining. For commercial spaces like this, the practical side of things matters just as much as the appearance. A coated floor is easier to keep clean, easier to spot debris on, and just flat out looks more professional. Customers notice. Tom and the crew at Heartland 4x4 are going to be enjoying this floor for a long time. Big thanks to Tom for trusting us with the job. If your shop, garage, or commercial space is sitting on tired concrete, this is the kind of upgrade that pays off every single day.
• 
  , MN

  Pebble Beach Garage Floor Coating in Little Falls

  Here's what we were working with - a garage floor covered in rust stains, paint splatters, and years of buildup ground right into the concrete. Not the kind of thing you can scrub away. The surface was tired, stained in multiple spots, and honestly just made the whole garage feel rough and unfinished. We went with Pebble Beach for this one. It's a flake blend that gives you a clean, neutral look without feeling cold or plain. The color works well in a garage that actually gets used - it hides minor dirt between cleanings and still looks sharp day to day. Bryan and Lori picked a good one. What makes this coating system worth it beyond just the looks is the durability. The floor gets a proper base coat, a full broadcast of decorative flakes, and a tough topcoat that seals everything in. The result is a surface that resists oil, chemicals, and everyday wear. Much easier to keep clean than bare concrete - a quick sweep or mop and you're done. One thing we always make sure to do is run the coating right up the base of the walls. That coved edge detail you see along the perimeter ties the whole floor together and makes cleanup even simpler. No gap where dirt can collect between the floor and the wall. It's a small thing that makes a big difference in how the finished space feels. This garage went from something you'd avoid spending time in to a space that actually looks like it belongs in the house. That's what a quality garage floor coating does - it pulls the whole room together and holds up through whatever you throw at it.
• 
  Brainerd, MN

  Lori's Garage Floor Gets a Coating System Built to Last

  Here's what we were working with - a concrete floor covered in oil stains, rust-colored spots, and years of absorbed grime. That kind of surface tells a story, and it's one most garage floors can relate to. Bare concrete is porous by nature, which means every drip, spill, and chemical sits right in and keeps eating away at it over time. For Lori's garage, we went with our full system - polyurea base coat, full vinyl flake broadcast, and a polyaspartic top coat in Slatestone. That combination isn't just about looks. Each layer is doing a job. The polyurea base bonds hard to the concrete and creates a solid foundation. The flake adds texture and depth. The polyaspartic top coat locks everything in and gives you a surface that's non-porous, UV stable, and genuinely tough. That UV stability piece matters more than people think. A lot of coatings yellow and dull out within a couple of years - especially in spaces that get direct sunlight through the garage door. Polyaspartic doesn't do that. You get a finish that holds its color and clarity long-term, without the chipping or peeling you'd see with lower-grade products. The Slatestone color ended up looking sharp in this space. It's a clean, neutral gray-flecked finish that works well in practically any garage. Clean lines edge to edge, consistent coverage, no blotchy spots or thin areas. That's what a proper prep and application process gets you. What we ended up with is a floor Lori can actually use - one that wipes clean, handles whatever gets dropped on it, and still looks great doing it. If your garage floor looks more like the before than the after, this is the kind of coating system worth getting right the first time.
• 
  Braintree, England

  Full Flake Garage Floor Coating Done in One Day in Brainerd

  This Brainerd garage got the full treatment - and we wrapped it up in a single day. That's one of the biggest things homeowners are surprised by when they go with a polyurea and polyaspartic system. No waiting around for days. You're back in your garage fast, with a floor that looks completely different than what you started with. Here's how the system works. We start with a polyurea basecoat, which bonds hard to the concrete and gives the whole system its foundation. From there, we do a full flake broadcast - meaning we cover the entire surface with decorative flake, wall to wall. No thin spots, no bare patches. This floor got done in the color Fortress, which is a sharp mix of grays, whites, and dark accents that works well in just about any garage setting. Once the flake is locked in, we apply a UV-resistant polyaspartic topcoat. That's what gives the floor its smooth, glossy surface - and more importantly, it's what protects everything underneath. Polyaspartic won't yellow in sunlight the way older epoxy products do. It's also non-porous, so oil, road salt, water, and whatever else ends up on your garage floor just sits on top and wipes away. Easy. A lot of people think garage floor coatings are purely about looks. And yeah, the finished product does look great. But the real win is how much easier the floor is to live with day to day. No more staining into the concrete. No more dusty gray slab that looks beat up six months after you clean it. Just a tough, sealed surface that holds up. If your garage floor is cracked, stained, or just tired-looking, a system like this is worth a serious look. The combination of polyurea, full flake, and a polyaspartic topcoat is one of the most durable setups available - and it's done in one visit.
• 
  Holdingford, MN

  Basement Floor Coating in Holdingford Gets a Cardinal Blend Upgrade

  Most basement floors are an afterthought. Cold, cracked, dusty - they just sit there taking up space. That's exactly what Lenore was dealing with before we came in. The concrete had visible cracks running across the surface, and the floor had that typical worn-out look that makes a basement feel more like a storage unit than usable space. Before we laid down a single drop of coating, we did the prep work right. That means grinding the concrete down with dust-controlled equipment, cleaning out those cracks, and making sure the surface was ready to bond properly. Skipping prep is how you end up with a floor that peels or bubbles within a year. We don't cut corners there. For this job, Lenore went with our Cardinal blend - a bold mix of grey, red, white, and black flakes that gives the floor serious character. We use a polyurea base coat followed by a polyaspartic topcoat. That combination is tough. It resists stains, handles moisture, and holds up to foot traffic without yellowing over time. It's a big step up from standard epoxy. The finished floor looks sharp edge to edge. What was once a dull, cracked slab is now a clean, finished surface that actually makes the space feel like part of the home. A good basement floor coating does that - it changes how the whole room feels. Lenore trusted us with it, and we're glad we could deliver something worth showing off. If your basement floor is still sitting there bare and forgotten, this is what's possible. Our basement floor coatings are built to last and designed to look good doing it.
• 
  Coon Rapids, MN

  Pebble Beach Garage Floor Coating That Ties the Whole Space Together

  Some garages are just built different. This one came to us already loaded - vintage signs, a classic C10 truck, Craftsman tool chests, the works. The customer had put serious time and money into making this space something special. The floor just needed to catch up. That's exactly what our Pebble Beach coating does. It's one of our most popular color blends, and it's not hard to see why. The light gray flake base with the subtle speckle pattern gives the floor a clean, unified look without competing with everything else going on in the space. It just works. What we love about a garage like this is that the floor becomes part of the whole picture. Heavy tool chests roll around on it. A pristine classic truck sits on it. Engine parts get swapped on it. It has to look great and hold up to real use. That's the balance a quality flake coating strikes - it's durable enough for a working garage but sharp enough for a showroom. We also want to give a shoutout to the folks in our community who keep sending their friends and neighbors our way. Referrals like this one mean everything to us. When someone trusts us enough to recommend our work to people they care about, we don't take that lightly. We show up and we make sure it's right. If your garage floor doesn't match the effort you've put into the rest of the space, that's worth fixing. A coating like Pebble Beach is one of the fastest ways to pull a garage together and actually make it feel finished.
• 
  Baxter, MN

  Garage Floor Coating Done Right in Basil

  We first connected with Bob and Shirley at a home show, and it didn't take long to see they were the kind of homeowners who actually care about doing things right. When they were ready to move forward on their garage floor, we were glad to be the ones they called. Here's what we were working with before we got started - raw, stained concrete with oil marks, debris, and years of wear ground into the surface. That kind of floor isn't just an eyesore. It absorbs spills, holds onto dust, and gets harder to deal with every season. Bare concrete is basically a sponge, and once it's saturated with grime and oil, no amount of sweeping or mopping is going to fix it. What we put down is a full flake floor coating system - a base coat locked into the concrete, color flakes broadcast across the surface, and a topcoat sealed over everything. The green, white, and dark flake blend they chose gives the floor a clean, finished look that also hides the kind of everyday dirt and scuffs that come with actual garage use. That's not an accident - it's one of the reasons flake systems are so popular. The practical side of it matters just as much as the look. A coated floor is far easier to clean than bare concrete. Spills wipe up instead of soaking in. It handles foot traffic, vehicle weight, and whatever else gets dragged across it without showing the wear the way raw concrete does. For a working garage, that's a big deal. Bob and Shirley trusted us with their space, and we're proud of how it came out. If your garage floor looks anything like the before, it might be time to stop putting it off.
• 
  East Gull Lake, MN

  Cabin Fever Cured With a Polyurea and Polyaspartic Garage Floor Coating

  Here's what we started with - a stained, dull concrete slab that had seen better days. Oil spots, discoloration, and bare concrete throughout. Nothing unusual, but definitely not a floor anyone was proud of. The steps leading into the house were original wood, functional but completely unfinished. We don't do epoxy. That's not us cutting corners - it's actually the opposite. Epoxy yellows, peels, and doesn't hold up the way it should. Instead, we use a polyurea base coat followed by a polyaspartic top coat with a full flake broadcast. That system is tougher, more flexible, and more UV stable than anything epoxy can offer. It's just a better product. The steps got the same treatment as the floor. We built out a custom three-tier step set and coated them to match the rest of the space perfectly. That consistency matters. When the steps and the floor flow together as one cohesive finish, the whole garage looks intentional - not like a patchwork of upgrades done over the years. The finished result speaks for itself. A clean, full-flake floor with a tight granite-style blend running wall to wall, with the steps matching seamlessly. The kind of finish that makes you actually want to spend time in your garage. Whether you're parking, working, or just storing stuff, it feels completely different when the floor looks this good. This is the standard we hold ourselves to on every single job. No shortcuts, no inferior materials, no compromises. If your garage floor is still bare concrete, it doesn't have to be.
• 
  Clear Lake, MN

  Worn Patio and Steps Get a Durable Polyurea Coating Upgrade

  Worn-out concrete has a way of dragging down the whole front of a house. When the surface is stained, flaking, and just generally beat up, it doesn't matter how nice everything else looks - the entryway still feels neglected. That's exactly what we were working with here. The patio and steps were showing their age in a big way, with surface deterioration and discoloration that no amount of cleaning was going to fix. Before any coating touches the concrete, the surface prep has to be right. We ran a diamond grinding machine across the entire patio to open up the concrete and give the coating a real mechanical bond. Skip this step and you're just putting a pretty finish on a bad foundation - it won't last. The grinding also pulls out any weak or contaminated surface material so what's underneath is solid and ready. Once the surface was prepped, we applied a polyurea base coat and went into a full flake broadcast. That means flakes go down edge to edge until the surface is completely saturated - no thin spots, no bare patches. The Sandstone color blend ties in naturally with the stone facade on the house, which is one of those details that makes the finished product feel intentional rather than just functional. A polyaspartic top coat seals everything in and gives it that clean, finished look you can see in the after shots. What makes this system worth it is the durability. Polyurea and polyaspartic coatings are resistant to UV, abrasion, and moisture - all things that destroy standard paint or sealer over time. The coating wraps fully over the step risers and treads too, which is a detail that matters both for appearance and for keeping the edges from chipping down the road. When you coat steps halfway, the exposed edges are always the first thing to go. This same system works on patios, porches, entryways, and pool decks. The color options are wide, the turnaround is fast, and the end result holds up in a way that cheaper alternatives simply don't. If your concrete is at the point where you're tired of looking at it, a patio coating like this is one of the more straightforward ways to fix it for good.